spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134 t-1 (3mm) bi-level led indicator part number: wp7104alup/2surdk-0l hyper red features z black case enhances contrast ratio. z wide viewing angle. z high reliability life measured in years. z moisture sensitivity level : level 3. z housing material: ppa. z housing ul rating : 94v-0. z high temperature resistant housing. z high glass transition temperature epoxy. z rohs compliant. description the hyper red source color devices are made with al- gainp on gaas substrat e light emitting diode. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. part no. dice lens type iv (mcd) [2] @ 20ma v iewing angle [1] min. typ. 2 1/2 hyper red (algainp) red diffused 400 900 40 *120 *240 wp7104alup/2surdk-0l symbol parameter device typ. max. units test conditions peak peak wavelength hyper red 645 nm i f =20ma d [1] dominant wavelength hyper red 630 nm i f =20ma ? 1/2 spectral line half-width hyper red 28 nm i f =20ma c capacitance hyper red 35 pf v f =0v;f=1mhz v f [2] forward voltage hyper red 1.95 2.5 v i f =20ma i r reverse current hyper red 10 ua v r = 5v parameter hyper red units power dissipation 75 mw dc forward current 30 ma peak forward current [1] 185 ma reverse voltage 5 v operating/storage temperature -40c to +85c
spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134 hyper red wp7104alup/2surdk-0l
spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134 wp7104alup/2surdk-0l tape dimensions (units : mm)
spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134 packing & label specifications wp7104alup/2surdk-0l terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
spec no: dsao1026 rev no: v.2a date: jun/12/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: f.t.liu e rp: 1102013134
|
